SPECIFICATIONS

GENERAL

• Signal Type Support
• DXLink Multi-Mode Fiber, Simplex
• (Connectivity between TX and Input Connection and Output Connection and RX requires matching model types, multimode to multimode or single mode to single mode. The backplane architecture of the Epica DGX 288 allows for single mode inputs to be routed to multimode outputs and vice versa)
• Compatible AMX Products
• Must be used in conjunction with an Epica 288 Matrix Switcher Enclosure and a DXLink Simplex Multimode Fiber Transmitter and/or Reciever including DXF-TX-MMS (FG1010-363) and DXF-RX-MMS (FG1010-563)
• Note: Can be used in conjunction with Duplex Transmitters and Receivers, however the system will maintain one-way simplex functionality. Simplex infrastructure does not support control transport over fiber (such as Ethernet, USB, IR, Serial Control or EDID); although when used as part of a complete AMX controlled solution that includes NX Control hardware, control can be provided if a supplemental independent network connection is used.
• Compatible Formats: HDMI Video / Audio over fiber
• Regulatory Compliance: See Epica 288 Matrix Switcher Enclosure for regulatory compliance
• Safety Certifications: Class 1 Eye Safe per requirements of IEC 60825-1 / CDRH

DXLINK FIBER

• Transport Layer Throughput: 10.3125 Gbps
• Video Data Rate (max.): 4.95 Gbps
• Video Pixel Clock (max.): 165 MHz
• Progressive Resolution Support: 480p up to 1920x1200,60 Hz
• Interlaced Resolution Support: 480i, 576i, 1080i
• 2K Resolution Support:
• 2048x1024,47Hz; 2048x1080,60Hz; 2048x1152,60Hz; 2048x1536,24Hz
• 2K formats are only compatible with DVI, HDMI, and DXLink Fiber Input/Output Boards and require the output or RX Scaler to be set in Bypass mode
• Deep Color Support: 24-bit
• Color Space Support:
• RGB 4:4:4
• YCbCr 4:4:4 and 4:2:2 (Input signal support is for YCbCr 4:4:4 and 4:2:2; output color-space is converted to RGB 4:4:4.)
• 3D Format Support:
• Frame Packing 1080p up to 24 Hz
• Frame Packing 720p up to 50/60 Hz
• Frame Packing 1080i up to 50/60 Hz
• Top-Bottom 1080p up to 24 Hz
• Top-Bottom 720p up to 50/60 Hz
• Side-by-Side Half 1080i up to 50/60 Hz
• The scaler on the corresponding DXLink Fiber RX must be set to Bypass mode.
• Audio Format Support: Dolby TrueHD, Dolby Digital, DTS-HD Master Audio, DTS
• 2 CH through 8 CH L-PCM
• Dolby Digital and DTS support up to 48 kHz, 5.1 channels
• Audio Resolution: 16 bit to 24 bit
• Audio Sample Rate: 32 kHz, 44.1 kHz, 48 kHz, 96 kHz, 192 kHz
• HDCP Support
• Full matrix HDCP support (includes any input to any or all outputs)
• Key Management System
• AMX HDCP InstaGate Pro® Technology
• Key support up to 16 destinations per output/receiver, independent of source device
• CEC Support: None
• Connectors: 16 LC Simplex Fiber ports (with an input and an output connector on each) conforming to ANSI TIA/EIA 604-10 (FOCIS 10A)
• Fiber Cable Types and Supported Length: OM3 50/125 mm @ 984 ft. (300 m)
• Optical Wavelength: 850 nm
• Multimode Optical Budget:
• 6.8 dB (typical) between DXLink Fiber transceivers
• Optical Modulation Amplitude (OMA): -4.3 dBm (min.)
• Optical Modulation Amplitude (OMA) Sensitivity: -11.1 dBm (typical)
• Multimode Optical Transceiver Mean Output Power: -1 dBm (average power)
• DXLink Fiber Input Port Propagation Delay: 5 ms
• DXLink Fiber Output Port Propagation Delay: 5 ms

CONNECTORS AND SIGNAL TYPES

• DXLink Fiber (LC Simplex) Transceiver (Signal support depends on the type of DXLink Fiber Transmitters and Receivers used.): HDMI with embedded digital audio DVI with or without HDCP or embedded digital audio Analog video input (RGBHV, RGBS, RGsB, Y/Pb/Pr) Digital audio or analog stereo audio

EDID RESOLUTIONS SUPPORTED THROUGH FIBER TRANSMITTER DOC

• Standard Timing Identification (Default Shipping EDID*): See the Epica DGX 288 Reference Manual for more information.